2CY series gear lubricating oil pump is mainly used for conveying lubricating oil in lubrication system of various mechanical equipment, which is suitable for conveying lubricating oil with viscosity of 10. Lubricating oil below 75c. S.T. and temperature below 300 ℃. Stainless steel gear pump can transport oil, beverage and low corrosive liquid without lubrication. Equipped with copper gear, it can transport low internal point liquid, such as gasoline, benzene, etc. In addition to ordinary motor, this series of pumps can also be equipped with explosion-proof motor of the same specification according to the needs of users.
Model meaning
一、2CY齒輪式輸油泵產品概述：
1、本泵適用于輸送各種有潤滑性的液體，溫度不高于70℃，如需高溫200℃，同本單位聯系可配用耐高溫材料即可，粘度為5×10-5～1.5×10-3m2/s。
2、本泵不適用于輸送腐蝕性的、含硬質顆粒或纖維的、高度揮發或閃點低的液體，如汽油、笨等。
本型泵在泵體中裝有一對回轉齒輪，依靠兩齒輪的相互嚙合，把泵內的整個工作腔分兩個獨立的部分。泵運轉時主動齒輪帶動被動齒輪旋轉，當齒輪脫開嚙合時在吸入側就形成局部真空，液體被吸入。被吸入的液體充滿齒輪的各個齒谷而帶到排出側，單級單吸油泵齒輪進入嚙合時液體被擠出而排出泵外。
二、2CY齒輪式輸油泵結構說明：
本產品由泵體、齒輪、前后泵蓋、安全閥、軸承及密封裝置等零、部件組成。
1、泵體、前后蓋等零件為灰鑄鐵件，齒輪用優質碳素鋼制作；亦可根據用戶需要用銅材或不銹鋼制作。
2、安全閥。
2CY系列齒輪式潤滑泵自身不帶安全閥，用戶在使用時需自行在管路系統中安裝安全閥。KCB,2CY系列齒輪式輸油泵在后泵蓋或泵體上方裝有安全閥，當泵或排出管道發生故障或?qū)⑴懦鲩y門完全關閉而產生高壓和高壓?擊時安全閥就會自動打開，卸除部分或全部的高壓液體回到吸入腔，從而對泵及管道起到安全保護作用。
3、軸承。
2CY系列齒輪式潤滑泵全部采用DU軸承；可根據用戶要求采用錫青銅軸承。&0818.3-83.3、2CY1.1齒輪式輸油泵采用DU軸承；可根據用戶要求采用錫青銅軸承。
KCB133-960、2CY8-60齒輪式輸油泵有采用DU軸承，錫青銅軸承和滾動軸承三種結構，需在訂貨時注明。訂貨時未注明者均按DU軸承結構供貨。 軸承為內置型式，依靠被輸送介質進行潤滑；011軸承和錫青銅軸承能在非潤滑性介質中工作。
4、軸封。
本系列產品的軸端密封有骨架油封、機械密封及填料密封三種結構。
a. 骨架油封：骨架油封的特點是維護、更換方便，成本低，但壽命較短。丁晴膠骨架油封適用于1001：以下工作環境；氟橡膠骨架油封適用于200℃以下工作環境。
b. 1機械密封：機械密封的特點是密封可靠、壽命長，成本高。機械密封的基體用不銹鋼制造， 動、靜環視介質不同分別由YG8硬質合金或YG8-石墨制造，使用溫度在200℃以下。
c. 填料密封：填料密封僅用于高溫油泵，其特點是耐高溫，有少量泄漏。使用過程中需根據泄漏情況經常進行調整，使用溫度在250℃：以下。
用戶需何種型式的密封結構需在訂貨時注明。凡訂貨時未注明者均按丁晴膠骨架油封結構供貨。
5、進、出油口型式。
2CY系列齒輪式潤滑泵進、出油口為與口徑對應的英制管螺紋（G),直接制作在泵體上。KCB18.3-200、2CY1.1-12齒輪式輸油泵配帶管螺?口的腰形法蘭；其余泵不配帶法蘭，當用戶需要配帶法蘭時，應在訂貨中注明。
6、泵與電機用彈性聯軸器連接，并安裝在公共底盤上。
Application scope of 2CY gear lubricating oil pump
1. The pump is suitable for conveying all kinds of liquid with lubricity. The temperature is not higher than 70 ℃. If the high temperature is 200 ℃, the high temperature resistant material can be used when contacting with the unit. The viscosity is 5 × 10-5 ～ 1.5 × 10-3 m2 / s.
2. The pump is not suitable for conveying corrosive, hard particles or fibers, highly volatile or low flash point liquid, such as gasoline, benzene, etc.
This type of pump is equipped with a pair of rotary gears in the pump body. Depending on the mutual engagement of the two gears, the whole working chamber in the pump is divided into two independent parts. When the pump is running, the driving gear drives the passive gear to rotate. When the gear disengages from engagement, a local vacuum is formed on the suction side, and the liquid is inhaled. The inhaled liquid fills each tooth valley of the gear and takes it to the discharge side. When the gear enters into meshing, the liquid is squeezed out and discharged from the pump.
